Some hams will insist that you need a particular chipset in the converter to avoid problems, but I guess I have been lucky: If needs be, the transformer can be removed without too much trouble and carried separately in the hold. With a quiet receiving location, birdies on the high bands are the most annoying so perhaps I should give that a try, next time I have the case open. That said, shortly before my K3 arrived, my old Sony laptop decided it was time to go to the big bit bucket in the sky. RS is a well-defined standard. Using a 30m fullwave loop on the subRX in my right ear and the beam, vertical or dipoles on the main RX feeding my left ear, I find diversity mode is worth about 3dB due to the loop partially filling-in QSB dips on the main antennas. Check out the spectrum anomalies on this BeaconSee output for example:
|Date Added:||21 August 2006|
|File Size:||51.35 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
As far as Vista is concerned, I don’t know. Not so cool for our 1kW limit in NZ. Elecraft W2 wattmeter I bought the W2 mostly to address a simple problem: Some hams will insist that you need a particular chipset in the converter to avoid problems, but I guess I have been lucky: Hopefully, it will not give you an error message but will kuab up the normal N1MM screen, now showing the frequency and mode from the rig in the title area of the elecraff data entry window.
A 30m Ethernet cable evidently introduces too much resistance, but looking at the circuit diagram, I see there are 1k resistors in most of the lines: The connection between pickup head and elfcraft box uses an Ethernet cable.
You can remotely-control and monitor the KPA with these if it is just out of reach, or somewhere across the planet. When tuning my old valve amp, the load and plate tuning is critical on some bands.
Free forum by Nabble. Play with the settings on dlecraft Operate tab if you like.
That said, shortly before my K3 arrived, my old Sony laptop decided it was time to go to the big bit bucket in the sky. One thing for sure, be VERY careful to use a cable between the K2 and the adapter that only connects the RS signals and not the K2-specific lines that appear on the connector on the K2. Mostly the KPA just sits there quietly doing its thing, as any well-behaved amp ought to do.
Having not updated my KPA in well over a year, I forgot how to do it, so here are my notes as a reminder for next time: Other software defined radios are updated from time to time but users appear to have little say in what changes are made by the manufacturers.
The kit instructions said nothing about which way to mount the fan and it had no markings to show which way it blows. A switch in the boom turns the mic on as it swivels down into place.
I have been a fan of Sennheiser headphones for about 25 years. Check tick just two options: The folder location rlecraft still be as you left it, if not find the directory where you store your KPA stuff in my case, C: I can use the CWT tuning indicator to zero-beat my transmitter more accurately on other callers.
Change, sub, unsub etc. I’ll be doing some more testing this weekend.
Elecraft Accessories – Transceiver Accessories – Amateur Radio
Open the Firmware tab. By comparison, the following screenshot from my TS shows no such obvious artifacts:. Kusbb the highest frequency reference you can receive a strong enough signal to discern its pitch clearly e.
Both my Elecraft radios are physically compact and lightweight. The Yaesu uses a traditional analogue meter which gives better resolution though probably worse accuracy than the W2. It may give you a message about having found and downloaded something new. Now figure out which serial port the adapter is using: WAV File column, instead of the file name of a.
Turn on your K3 and wait a good while e. Tape the Menu key to exit the settings.
Search everywhere only in this topic. Both are ‘no-name’ devices and both use FTDI chipsets http: